T862 IRDA Welder Infrared SMT SMD BGA Rework Station

Description

T862  IRDA Welder REWORK STATION
NOTE： we don't ship the item to PO BOX address， and we only ship the item to English address,
s please leave us your physical English address when you pay.
Technical Parameter
Work bench size 410x
316mm
Rated voltage and frequency AC220-230v/AC110V   60/50Hz
Complete machine power 1600W
Preheating plate power 1500W
Preheating plate size 280x
270mm
Preheating plate temperature adjustable 0
-450
℃
Main Components:
Preheating plate main body 1
Temperature sensor 1
PCB board holder 1
Power line 1
User manual (compact disc) 1
Main component function explanation
：
Compare with T860,IRDA WELDER add a Rework 936 and a 936 switch,more concenient than before.
1. Adopt infrared weld technology which independent exploration.
2. Use infrared heat,it is easy to cut through,heat proportion piercing tradition weld machine with sirocco.
3. Easily operate.Just need one day training.Can operation this machine.
4. No need weld tools,it can weld all the component of 15x15-25x
25mm
.
5. This machine has 650W heating system.widely to 80x
120mm
.
6. Infrared heating no have sirocco flow. Don't impact perimeter small component.Can suitable for all of the
component,especially Micro BGA component.
Parameter
：
Working voltage : AC220V 50Hz
Output power: 800W
Temperature:
100
℃
-350
℃
Operation method
1
、
Boot.
①
Check the power source,wind the plug.
②
Turn on the power source.Don’t use until pass check.Pand will display enactment value.When last time used.
③
Installation the repair shell.Fix the line on the strip rack.Screw the light system height.Keep 20-30mm between light and welder machine.
④
According to measurement of welder piece.Proprictily screw temperature.from60
℃
-350
℃
.When you strip 15×15mm piece.Choice temperature 240-300
℃
.When you strip 25×25mm piece.Choice temperature 300-350
℃
.The temperature come up to 350
℃
.The light system will shoot straightly.Please pay more attention to yourself control time.avoid burn out.
⑤
Screw focus.The light system smallest diameter is 15mm .the biggest is 30mm.Normally keep 20-30mm.
⑥
Turn on the two switches.They control warm-up plate and light system.
2
、
Dismantle and weld
。
①
Regulate temperature , make the chip focus
②
After suitable for timing, the tin is clicked and melted, take out the chip
。
3
、
Weld the chip
。
①
Clean the pad
。
②
Coating help solder flux (should not thick too , can have first more thin ) and soldering tin ball
。
③
Wait to help the solder flux to volatilize into the flux, heat and totally melt to the tin ball , place correctly with the clip , aim at the chip to weld into the position.
④
936 searing-iron.Open the swich and enactment temperature.
Caution!
1
、
After use , imprison power immediately , make sure the light body cooling down,and place it in safety.After turning off the power switch
2
、
Keep the blowing way without hindered, the light body is clean.
3
、
The support in good time is polished with the oil to lead the post , focus
4
、
Disconnect the plug when you don’t use the it for a long time.
5
、
Operate carefully, take care
。
Shipping Policy
We will send out the item within 2-3 days through DHL/EMS/FEDEX /UPS/SPEEDPAK/CHINA POST to the below countries:
Belgium, Netherlands, Luxembourg, Italy, Germany, France, United Kingdom, San Marino;
Austria ,Denmark ,Finland ,Greece ,Ireland ,GUERNSEY ,JERSEY ,Norway ,
Portugal , spain , Sweden , Switzerland;
Bulgaria,Cyprus,Estonia,Latvia,Lithuania,Malta,slovakia,slovenia;
Czech Republic, Hungary, Poland, Romania,.
Australia ,New Zealand ,Korea South, Malaysia, Thailand, Philippines ,Singapore , Bruniei ,Taiwan , Macau, Indonesia,
USA, Canada
We will send tracking number to your eBay email within 1 day after sending out your item
We will mark the item at the very low value, so that you do not need to pay for the tax or pay a little tax.
Payment policy:
We accept Paypal only.
Payments must be finished within 5 working days after bid, otherwise, Unpaid Item dispute will be reported to eBay.
Refund &Return policy
We take all the responsibility during delivery. If you do not receive your item, we will refund you the full money or send you a new item according to your request.
We can accept the return item within 60 days after the buyer receives it. Once we receive the return item, then we will refund you full money.
Feedback Policy
We will very appreciate you give us positive feedback
ASAP.  If the item you got in any problem, PLS don’t hesitates to contact us.  We will do our best to help solve the problem